A Step-by-Step Guide to Setting Up a Tub
A Step-by-Step Guide to Setting Up a Tub
Blog Article
We have found the article on Installing A Bathtub down the page on the internet and felt it made good sense to write about it with you in this article.
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably difficult project. If the old tub is easily obtainable, the task can move quickly; if you have to open a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. See to it you have qualified yourself for the job as well as fit attempting it. As opposed to hiring a professional to take control of a halfway-completed project, it is much better to take into consideration employing one before you start. Chances are you may require an expert plumber to make tube links.
This post will assist you install a brand-new bath tub in your shower room if you have actually currently purchased a brand-new tub and also don't require to change the plan of your previous water system pipes.
Your devices as well as product checklist need to make up the following:
Planning for the Setup
To start with, the supporting frame supplied with the bathroom ought to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is detach the water supply. After doing so, activate the taps to drain any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome as a result of the limited access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, place the bath tub in the required placement. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bath tub until the level reads level.
To mount taps, fit all-time low of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; after that do the very same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub as well as additionally check the overflow outlet and also the regular outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bath tub needs to wait until the bathtub has actually been made use of at the very least when as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a stiff seal, triggering the water to penetrate the wall surface in between the bath and the tiling, leading to difficulties with moisture as well as possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can break rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on Installing A Bathtub, I imagined sharing that excerpt was really helpful. Sharing is nice. Helping others is fun. Kudos for your time. Please pay a visit to our blog back soon.
Book A Service Call
Report this page